Whishlist (0) Contact us

Présentation

6U CompactPCI Managed Ethernet Switch with 10GbE Uplinks

The ADLINK cPCI-6S10 is a 6U CompactPCI Ethernet switch blade designed for embedded systems using a compatible PICMG 2.16 backplane.

It integrates the Broadcom BCM56150 switch with an ARM Cortex-A9 processor and provides 24 Gigabit Ethernet ports together with two 10 Gigabit Ethernet SFP+ uplinks.

Connectivity includes twenty Gigabit Ethernet ports routed to rear connectors J3/J5, three front-panel Gigabit Ethernet ports and one additional optional port through J4.

Layer 2/3 Switching and PacketManager Network Administration

The cPCI-6S10 supports Layer 2/3 networking functions, including IEEE 802.1Q VLANs, Quality of Service (QoS), IPv6, IEEE 802.3ad link aggregation and Spanning Tree protocols.

ADLINK PacketManager provides network administration, port configuration and traffic management capabilities.

The board also includes an RS-232 console port and an Ethernet management interface. IPMI enables hardware monitoring and system management.

Maintaining or Replacing an End-of-Life CompactPCI Switch

The cPCI-6S10 is officially listed as End of Life (EOL) by ADLINK. This status must be considered when maintaining existing CompactPCI installations or planning equipment upgrades.

Replacement assessment requires verification of backplane compatibility, rear connectivity, port configuration, Ethernet throughput, network functions and mechanical requirements.

ECRIN Systems supports embedded equipment lifecycle management through its obsolescence management services.

For new developments, alternative networking technologies can be explored, including SOC-E rugged TSN Ethernet switches and ECRIN Systems rugged switching solutions.

These products have different form factors and interfaces and should not be considered direct plug-in replacements for the cPCI-6S10.

Discover the ADLINK embedded computing portfolio at ECRIN Systems, supported by our technical teams in Crolles, France.

Specifications

INTERFACE
Ethernet:
Twenty 1000BASE-T ports to J3/J5 for node slots
Three 1000BASE-T ports to front panel
Two 10 Gigabit ports to front panel for uplink
One 10/100/1000BASE-T port to J4 for optional applicaiton
One 10/100BASE-TX port PHY to front panel for remote management

Management:
500 kB on-chip frame buffer
DSCP remarking for both IPv4 and IPv6
Jumbo frame support
Programmable classifier for QoS, IEEE802.1p and DSCP for IPv4 and IPv6
8k MAC addresses and 4k VLANs (IEEE 802.1Q)
Flexible link aggregation compliant to IEEE 802.3ad
Full-duplex flow control (IEEE 802.3x) and half duplex back pressure,
symmetric and asymmetric multiple protocol support: IEEE 802.1D, IEEE
802.1w, IEEE 802.1s and IEEE 802.1X
COM
One RJ-45 RS-232 console port on front panel for management
PROCESSOR & SYSTEM
-
Switch Fabric
Broadcom BCM56150 24-port Gigabit Ethernet switch with two 10 Gigabit
SFP+ uplink ports, integrated ARM Cortex-A9 processor
PHY
Broadcom BCM54685 Octal port 1000BASE-T PHY
Broadcom BCM5221 100M PHY
CPU
ARM Cortex-A9 CPU integrated in Broadcom BCM56150
Flash
8MB SLC QSPI NAND flash
PICMG standards
PICMG 2.0 CompactPCI R3.0
PICMG 2.9 System Management R1.0
PICMG 2.16 Packet Switch Backplane R1.0
OPERATING SYSTEMS OS
Broadcom SDK under Linux (Please contact ADLINK for other OS support)
MISCELLANEOUS
-
LEDs
Power Good, 24-port 1000BASE-T, 2-port 10 Gigabit
Hardware Monitor
Monitors voltages of CPU, switch and PHY by IPMI
Reset Button
Passive reset button on front panel for blade reset
MECHANICAL & ENVIRONMENTAL
-
Form Factor
6U 4HP (single slot)
233.35mm x 160mm (L x W)
Operating Temperature
0°C to +60°C for air cooled
Storage Temperature
-50°C to +100°C
RH Humidity
95% non-condensing
Shock
15G peak-to-peak, 11ms duration, non-operating
Vibration
2Grms random vibration between 5-500Hz in 3 axis, operating
SAFETY & EMI
Certification
CE/ FCC Class A

Resources & documentation

Need to Maintain or Replace Your cPCI-6S10 CompactPCI Switch?

Need to Maintain or Replace Your cPCI-6S10 CompactPCI Switch?

Is your existing system using an ADLINK cPCI-6S10 switch blade?

ECRIN Systems can help review your maintenance or replacement requirements, including backplane compatibility, Ethernet connectivity, management functions and environmental constraints.

Contact our technical team to assess available options and identify a suitable approach for your existing equipment.

Other Embedded Ethernet Switching Solutions

See the range
XMC-TSN / XMC-10TSN – XMC Ethernet TSN Switch Card 1/10GbE

XMC-TSN / XMC-10TSN – XMC Ethernet TSN Switch Card 1/10GbE

The XMC-TSN and XMC-10TSN are Ethernet TSN switching cards in XMC mezzanine form factor, designed for critical embedded systems. They offer up to 17 configurable ports, 1GbE/10GbE connectivity depending on version, IEEE 802.1AS synchronization and a reconfigurable FPGA platform.
MIL-10TSN – Rugged Military Ethernet TSN Switch 1/10GbE

MIL-10TSN – Rugged Military Ethernet TSN Switch 1/10GbE

The MIL-10TSN is a rugged military Ethernet TSN switch designed for embedded networks requiring deterministic communications. It combines Gigabit copper and 1/10GbE fiber interfaces with time synchronization, redundancy and cybersecurity functions in a fanless IP66 enclosure..
QUARTZ rugged switch

QUARTZ rugged switch

The QUARTZ is a compact, ruggedised Ethernet switch designed for embedded networks and challenging environments. It offers up to 8 Gigabit Ethernet copper ports and 2 fibre ports, with L2/L3 functions, PTP synchronisation and TSN support depending on the version, in a housing with MIL-DTL-38999 connectors.