Whishlist (0) Contact us
Filter
TQMC802 – 4-Channel Isolated CAN FD QMC Module, 5 Mbps

TQMC802 – 4-Channel Isolated CAN FD QMC Module, 5 Mbps

The TQMC802 is a VITA 93.0 QMC module with four independent, galvanically isolated CAN FD interfaces. It supports CAN FD and Classical CAN, with data rates up to 5 Mbps and configurable termination on each channel.
TQMC801 – 1000BASE-KX Gigabit Ethernet QMC Module with PTP

TQMC801 – 1000BASE-KX Gigabit Ethernet QMC Module with PTP

The TQMC801 is a VITA 93.0 QMC Gigabit Ethernet 1000BASE-KX module. It features an Intel I210IS controller, IEEE 1588/802.1AS PTP synchronization and AVB traffic-shaping capabilities with appropriate software support.
TQMC800 – Gigabit Ethernet 10/100/1000BASE-T QMC Module

TQMC800 – Gigabit Ethernet 10/100/1000BASE-T QMC Module

The TEWS Technologies TQMC800 is a VITA 93.0 QMC Gigabit Ethernet module featuring an Intel I210IT controller. It supports 10/100/1000BASE-T, IEEE 1588/802.1AS synchronization and AVB capabilities with appropriate software support.
TQMC701 – 16-bit Analog and Digital Multifunction QMC Module

TQMC701 – 16-bit Analog and Digital Multifunction QMC Module

The TQMC701 is a VITA 93.0 QMC module combining eight 16-bit analog inputs, programmable analog outputs and 16 TTL digital I/O lines. It supports simultaneous sampling, conversion sequencers and DMA transfers.
TQMC700 – FPGA QMC Module with 8 × 18-bit ADC and 8 × 16-bit DAC

TQMC700 – FPGA QMC Module with 8 × 18-bit ADC and 8 × 16-bit DAC

The TQMC700 combines an AMD Artix 7 FPGA, eight simultaneously sampled 18-bit analog inputs, eight 16-bit analog outputs and 16 TTL digital I/O lines in a VITA 93.0 QMC module.
TQMC605 – AMD Artix 7 FPGA QMC Module with 40 Direct I/O Lines

TQMC605 – AMD Artix 7 FPGA QMC Module with 40 Direct I/O Lines

The TQMC605 is a reconfigurable VITA 93.0 QMC FPGA module featuring an AMD Artix 7 and 40 I/O lines directly connected to the FPGA. It supports application-specific digital logic development using AMD Vivado.
TQMC604 – 32 Isolated Digital Outputs QMC Module, 0.15 A

TQMC604 – 32 Isolated Digital Outputs QMC Module, 0.15 A

The TQMC604 is a VITA 93.0 QMC module with 32 isolated digital outputs operating from 5 to 36 V DC and supporting up to 0.15 A per channel. It includes electrical protection and a programmable hardware watchdog.
TQMC603 – 20 Isolated Digital Outputs QMC Module, 0.3 A

TQMC603 – 20 Isolated Digital Outputs QMC Module, 0.3 A

The TEWS Technologies TQMC603 is a VITA 93.0 QMC module featuring 20 isolated digital outputs operating from 5 to 36 V DC at up to 0.3 A per channel. It combines three switching modes, electrical protection and a programmable hardware watchdog.
TQMC602 – QMC Module with 16 Isolated Digital Inputs and Outputs

TQMC602 – QMC Module with 16 Isolated Digital Inputs and Outputs

The TQMC602 combines 16 isolated 15–60 V digital inputs and 16 isolated 5–36 V digital outputs in a VITA 93.0 QMC module. It supports digital-state acquisition, output control, input debouncing and a programmable hardware watchdog.
TQMC601 – 32-Channel Isolated Digital Input QMC Module

TQMC601 – 32-Channel Isolated Digital Input QMC Module

The TQMC601 is a VITA 93.0 QMC module featuring 32 isolated digital inputs for 15 to 60 V DC signals. It provides programmable debouncing and configurable interrupts for digital-state acquisition in industrial and embedded systems.
TQMC600 – Artix 7 FPGA QMC Module with Configurable Digital I/O

TQMC600 – Artix 7 FPGA QMC Module with Configurable Digital I/O

The TQMC600 is a VITA 93.0 QMC reconfigurable FPGA module featuring an AMD Artix 7 device. It supports application-specific digital I/O functions through 5 V-tolerant TTL, EIA-422/EIA-485 or M-LVDS interfaces, depending on the variant.
TQMC402 – 4-Channel Isolated RS232/RS422/RS485 QMC Module

TQMC402 – 4-Channel Isolated RS232/RS422/RS485 QMC Module

The TQMC402 is a VITA 93.0 QMC module featuring four galvanically isolated RS232, RS422 or RS485 serial interfaces. Each channel is independently programmable and supports asynchronous communication up to 20 Mbps in RS422/RS485 modes.
TQMC401 – 4-Channel High-Speed Synchronous/Asynchronous Serial QMC Module

TQMC401 – 4-Channel High-Speed Synchronous/Asynchronous Serial QMC Module

The TQMC401 is a VITA 93.0 QMC module featuring four high-speed synchronous and asynchronous serial channels. Its FPGA-based controller supports multiple protocols, DMA transfers and synchronous data rates up to 10 Mbps.
TQMC400 – 4-Channel QMC RS232/RS422/RS485 Full-Modem Serial Module

TQMC400 – 4-Channel QMC RS232/RS422/RS485 Full-Modem Serial Module

The TEWS Technologies TQMC400 is a VITA 93.0 QMC module featuring four programmable RS232, RS422 or RS485 serial channels. It supports asynchronous communication up to 20 Mbps in RS422/RS485 modes and provides full RS232 modem signals.
TCPS210 – 3U CompactPCI Serial Carrier with 3 QMC Sites

TCPS210 – 3U CompactPCI Serial Carrier with 3 QMC Sites

The TCPS210 is a 3U CompactPCI Serial QMC carrier conforming to PICMG CPCI-S.0 R3.0. It supports up to three single-width VITA 93.0 QMC modules, with PCIe Gen3 x4 connectivity and rear I/O through P2, P3 and P4 connectors.
TPCE210 – PCI Express Gen2 x4 Dual QMC Carrier Board

TPCE210 – PCI Express Gen2 x4 Dual QMC Carrier Board

The TEWS Technologies TPCE210 is a low-profile PCI Express Gen2 x4 carrier board. It supports two single-width VITA 93.0 QMC modules or one double-width module, with front-panel I/O access through a VHDCI-68 connector.
TVNX210 – 19 mm VNX+ Dual QMC Carrier Module

TVNX210 – 19 mm VNX+ Dual QMC Carrier Module

The TEWS Technologies TVNX210 is a 19 mm VNX+ carrier conforming to ANSI/VITA 90.0-2026. It supports two single-width QMC modules or one double-width module, with PCIe Gen3 x4 and rear I/O routing to the VNX+ backplane.

Applications of TEWS Embedded I/O Modules and Interface Boards

TEWS solutions address a wide range of communication, data acquisition and control requirements in embedded electronic equipment. Selecting the appropriate module depends on the signal characteristics, communication protocols, host platform and operating conditions.

Defense, Aerospace and Mission-Critical Embedded Systems

Mission-critical systems frequently require multiple communication and I/O interfaces to exchange data with sensors, electronic equipment and onboard subsystems.

TEWS modules can provide serial communication interfaces, analog acquisition channels, isolated digital I/O and FPGA-based processing functions within compact electronic platforms.

QMC modules and compatible carrier boards are particularly relevant for systems where physical space, cooling requirements and I/O flexibility must be considered during the design process.

Module selection and any applicable environmental qualification requirements must be validated for the complete system.

Discover ECRIN Systems' Defense, Aerospace and Security solutions.

Naval and Maritime Electronic Systems

Naval electronic systems require appropriate solutions for signal acquisition, communication between onboard equipment and the management of dedicated interfaces.

Embedded I/O boards can support the interconnection of computers, monitoring equipment, control devices and data acquisition systems.

The selection of serial, digital, analog or Ethernet interfaces depends on the equipment involved and the communication protocols used.

TEWS modules can be considered as expansion components for naval electronic systems, subject to compatibility assessments and validation against the environmental and operational requirements of each project.

Explore our rugged computing solutions for naval applications.

Industrial Automation, Control and Data Acquisition

Industrial applications frequently require additional acquisition, monitoring and control capabilities within embedded computing platforms.

TEWS digital input modules support the acquisition of electrical states, while digital output modules provide control signals within their specified electrical operating limits.

Analog I/O boards perform analog-to-digital and digital-to-analog conversion, enabling electronic systems to acquire and generate analog signals.

RS232, RS422 and RS485 interfaces provide serial communication capabilities for connecting industrial equipment and electronic subsystems.

These functions can be combined within a single computing platform using compatible QMC carrier boards.

Transportation, Energy and Communication Infrastructure

Electronic equipment used in transportation, energy infrastructure and distributed systems may require several communication interfaces.

The TEWS portfolio includes Gigabit Ethernet modules, CAN FD interfaces and programmable serial communication boards.

Depending on the product, additional features are available, including IEEE 1588 synchronization capabilities on the TQMC801 Ethernet module and galvanic isolation of the CAN FD channels on the TQMC802.

Integration requirements must be assessed according to the communication protocols, electrical characteristics and operating conditions of the application.

Test Equipment, Instrumentation and OEM System Development

Test benches, measurement equipment and OEM electronic systems often require multiple channels for signal acquisition and generation.

TEWS analog and FPGA modules can support the development of dedicated I/O functions, including multichannel acquisition, analog-to-digital conversion, signal generation and programmable logic processing.

PCI Express and CompactPCI Serial carrier boards also provide integration options for development platforms and electronic test systems.

TEWS Embedded I/O Boards and Modules: Technologies and Interfaces

The TEWS Technologies portfolio includes several families of embedded I/O modules, each designed to provide specific acquisition, control or communication functions.

The products available through ECRIN Systems address different requirements, from serial communication and digital I/O to FPGA processing and Ethernet connectivity.

QMC VITA 93.0 Modules: Compact Embedded I/O Expansion

QMC (VITA 93.0) is a compact mezzanine module standard developed for embedded electronic systems requiring additional input/output functions within a limited space.

The standard defines mechanical and electrical characteristics for integrating QMC modules into compatible carrier boards and host systems.

It supports configurations designed for air-cooled or conduction-cooled environments and uses PCI Express for module interconnection.

TEWS QMC modules provide a range of embedded I/O functions, including serial communication, digital input/output, analog acquisition, Ethernet, CAN FD and FPGA-based processing.

Compatibility must be verified for each module and carrier board combination, taking into account PCIe connectivity, I/O routing, mechanical dimensions and cooling requirements.

RS232, RS422 and RS485 Serial Communication Interfaces

Serial communication remains widely used in industrial equipment and embedded electronic systems.

TEWS offers several QMC modules supporting serial communication requirements:

  • TQMC400 – Four programmable RS232, RS422 or RS485 serial channels with modem signal support.
  • TQMC401 – Four high-speed serial communication channels supporting synchronous and asynchronous operation, with multiple transmission modes and protocols.
  • TQMC402 – Four programmable, galvanically isolated RS232/RS422/RS485 channels with data rates up to 20 Mbit/s.

Choosing the appropriate module depends on the communication protocol, required data rate, synchronization requirements, transmission mode and the need for electrical isolation.

These solutions are relevant for embedded systems requiring communication with sensors, control equipment or other electronic subsystems.

Isolated Digital Input and Output Modules

TEWS digital I/O modules enable embedded systems to monitor electrical states and generate control signals.

The range includes several modules with different channel configurations and electrical characteristics.

  • TQMC601 – 32 Isolated Digital Inputs: Provides 32 input channels operating from 15 to 60 V DC, with IEC 61131-2 Type 3 input characteristics and interrupt management.
  • TQMC602 – 16 Isolated Digital Inputs and 16 Outputs: Combines acquisition and control functions within a single QMC module, with output current up to 0.3 A per channel.
  • TQMC603 – 20 isolated digital outputs: Supporting a 5 to 36 V supply range and a maximum output current of 0.3 A per channel.
  • TQMC604 – 32 Isolated Digital Outputs: Features 32 output channels with a maximum current of 0.15 A per channel.

These modules address different embedded control requirements.

The selection process should consider the number of channels, voltage levels, switching characteristics, electrical protection features and integration constraints.

Analog Data Acquisition and Multifunction I/O Modules

Analog I/O interfaces provide signal conversion capabilities between external electronic equipment and digital processing systems.

TEWS offers analog acquisition and multifunction modules suitable for different measurement and signal-generation requirements.

  • TQMC700 – A reconfigurable FPGA-based multifunction module combining eight analog-to-digital channels, eight digital-to-analog channels and 16 digital I/O lines.
  • TQMC701 – A multifunction I/O module integrating eight 16-bit analog inputs, eight 16-bit analog outputs and 16 digital I/O lines.

The appropriate module depends on the required resolution, sampling rate, voltage ranges, number of channels and galvanic isolation requirements.

These solutions can support instrumentation, embedded data acquisition, testing and electronic control applications.

Reconfigurable FPGA Modules for Custom Embedded I/O

Field-Programmable Gate Arrays (FPGAs) enable the implementation of application-specific digital logic functions.

TEWS offers QMC FPGA modules based on AMD Artix-7 technology, providing configurable I/O capabilities for embedded electronic systems.

  • TQMC600 – Reconfigurable FPGA with Digital I/O: Supports up to 32 5 V-tolerant TTL I/O lines or 16 differential lines, depending on the variant.
  • TQMC605 – Artix-7 FPGA with 40 Digital I/O Lines: Provides 40 digital I/O lines connected directly to the FPGA, with electrostatic discharge protection.

These modules are intended for projects requiring programmable logic functions and application-specific I/O behavior.

FPGA development and the validation of electrical interfaces must be adapted to the requirements of the host system.

CAN FD and Gigabit Ethernet Embedded Interfaces

Communication between electronic subsystems is an important requirement in industrial and embedded computing applications.

The TEWS portfolio includes modules supporting CAN FD and Gigabit Ethernet connectivity.

The TQMC802 provides four independent, galvanically isolated CAN FD channels.

It supports both CAN FD and classical CAN communication, with programmable data rates up to 5 Mbit/s.

For Ethernet connectivity, TEWS offers:

  • TQMC800 – A Gigabit Ethernet interface : Supporting 1000BASE-T communication.
  • TQMC801 – 1000BASE-KX Gigabit Ethernet QMC Module: Features an Intel I210IS Ethernet controller, IEEE 1588/802.1AS synchronization support and IEEE 802.1Qav Audio Video Bridging capabilities with appropriate software support.

The TQMC801 is an Ethernet interface module rather than a complete TSN Ethernet switch.

Synchronization and traffic management functions must therefore be evaluated within the complete network and software environment.

QMC Carrier Boards: PCI Express, CompactPCI Serial and VNX+

QMC modules require a compatible carrier board or host platform providing the necessary electrical and mechanical interfaces.

TEWS offers several carrier boards designed for different embedded computing standards.

TPCE210 – PCI Express QMC Carrier Board

The TPCE210 is a low-profile PCI Express Gen2 x4 carrier board.

It supports two single-width QMC modules or one double-width module, providing an integration option for PCI Express-based computing platforms.

TCPS210 – 3U CompactPCI Serial QMC Carrier Board

The TCPS210 provides three single-width QMC slots within a 3U CompactPCI Serial platform.

It features PCIe Gen3 x4 connectivity and routes I/O signals to the rear connectors of the CompactPCI Serial system.

TVNX210 – QMC Carrier Module for VNX+

The TVNX210 is a 19 mm VNX+ carrier module supporting two single-width QMC modules or one double-width QMC module.

It provides a PCIe Gen3 x4 interface and routes QMC I/O signals to the VNX+ backplane.

These carrier boards enable the integration of multiple TEWS I/O functions into different computing platforms, provided that mechanical, electrical and thermal compatibility requirements are satisfied.

How to Choose the Right TEWS Embedded I/O Module

Selecting an embedded I/O module starts with identifying the required function, followed by an assessment of electrical characteristics, performance requirements and system integration constraints.

Technical requirement TEWS modules to consider
RS232, RS422 or RS485 serial communication TQMC400, TQMC402
High-speed synchronous or asynchronous serial communication TQMC401
Acquisition of 32 isolated digital input signals TQMC601
Combined digital inputs and outputs TQMC602
Isolated digital output control TQMC603, TQMC604
Multifunction analog and digital I/O TQMC700, TQMC701
FPGA-based logic and configurable I/O TQMC600, TQMC605
Multichannel CAN FD communication TQMC802
Embedded Gigabit Ethernet connectivity TQMC800, TQMC801
PCI Express, CompactPCI Serial or VNX+ integration TPCE210, TCPS210, TVNX210

 

This table provides an initial technical overview. Final product selection depends on the detailed specifications, available variants, compatibility with the host system and the manufacturer's current product status.

Integrating TEWS I/O Modules into ECRIN Systems Computing Platforms

Selecting an embedded I/O module is closely linked to the characteristics of the computing platform in which it will operate.

Mechanical dimensions, power requirements, signal routing, thermal management, software drivers and environmental constraints all influence the integration process.

ECRIN Systems supports industrial customers and system integrators in the development and integration of industrial and embedded computing solutions using COTS components and configurable systems.

Depending on project requirements, this support may include:

  • Selecting compatible I/O modules and carrier boards.
  • Assessing electrical, mechanical and thermal integration constraints.
  • Integrating interface boards into suitable computing platforms.
  • Defining the required configuration and specific developments.
  • Supporting testing, documentation and system lifecycle management.

TEWS products can therefore contribute to projects requiring dedicated embedded I/O functions as part of a COTS or Modified COTS approach.

However, integration with a specific ECRIN Systems computing platform must be assessed and validated for each application.

Discover our COTS and Modified COTS expertise.

FAQ: TEWS QMC Modules, Embedded Interfaces and System Integration

Integrate TEWS Embedded I/O Modules into Your Next System

Are you looking for an RS232/RS422/RS485 serial interface, an analog acquisition board, isolated digital I/O, an FPGA module or a CAN FD or Ethernet communication solution?

ECRIN Systems supports the selection of TEWS Technologies embedded I/O solutions and the evaluation of their integration into PCI Express, CompactPCI Serial and VNX+ platforms.

Our technical team can review your interface requirements, electrical characteristics, cooling constraints, expansion needs and operating conditions to identify the modules and configurations best suited to your project.

Whether you require a standard embedded I/O board or a computing system with application-specific interfaces, we can help you assess the available technical options.

Share your specifications, integration requirements or preferred TEWS references with our team.

Request for information

Please enter the requested information.

Learn More About QMC VITA 93.0 and VNX+ Technologies

TEWS Technologies Introduces Its VITA 93 QMC Portfolio

Explore TEWS Technologies' embedded I/O portfolio, its range of QMC modules and the carrier boards designed for compact embedded computing platforms.

Read our article about TEWS Technologies and QMC VITA 93.

VNX+: A Standard for Compact Embedded Computing Systems

Discover the VNX+ form factor, its integration principles and the role of the TEWS TVNX210 QMC carrier module in compact embedded computing applications.

Read our article about the VNX+ standard.