Whishlist (0) Contact us

Présentation

The Acromag QMC510 is a VITA 93 QMC serial communication module designed to add eight asynchronous serial interfaces to embedded computing systems. Each port can be individually configured for RS-232, RS-422 or RS-485 operation, with a PCI Express connection to the carrier board and host system.

This compact mezzanine module addresses multichannel communication requirements in industrial equipment, test systems and embedded defense and aerospace applications. Its eight ports operate independently but are non-isolated and share a common return connection.

Eight Programmable Serial Ports with 256-Byte FIFOs

The QMC510 allows individual software configuration of serial interface type, baud rate, character length, parity and stop bits.

RS-485 interfaces support full- and half-duplex operation. The specified maximum data rate reaches 20 Mbps, depending on interface configuration and communication conditions.

Each port includes 256-byte transmit and receive FIFO buffers, with programmable trigger levels. Interrupt functions support receive, transmit and communication-status events while reducing host processor interaction.

A general-purpose 16-bit timer/counter with a 125 MHz internal clock also supports single-shot and retriggerable timing operations.

VITA 93 Form Factor and QMC Carrier Board Integration

Measuring 78.25 × 26 × 11 mm, the QMC510 uses the single-width QMC mezzanine form factor. Two 80-pin connectors provide separate host connectivity and field I/O interfaces.

Its PCI Express Gen 1 x1 interface enables communication through a compatible QMC carrier board. Depending on the selected carrier, the module can be incorporated into PCI Express, VPX, CompactPCI or VNX+ embedded platforms.

An onboard EEPROM accessible over I²C also allows a smart carrier equipped with an IPMC controller to retrieve module information for supported management functions.

The QMC510 extends the Acromag embedded computing and I/O portfolio with compact, high-density serial connectivity.

QMC511 Air-Cooled and QMC512 Conduction-Cooled Versions

The QMC510 family is available in two ordering configurations:

  • QMC511-1111: air-cooled version, operating from 0 to +70°C with 200 LFM airflow.

  • QMC512-1111: conduction-cooled version, operating from −40 to +85°C.

These versions allow module selection according to system cooling and thermal operating requirements.

Both provide eight non-isolated serial ports. Applications requiring galvanic isolation must use a suitable alternative module.

Applications and Acromag Technical Support in France

The QMC510 supports communication with multiple serial devices, data collection, test equipment and serial interface expansion in embedded computers.

Typical applications include industrial systems, defense electronics and aerospace equipment requiring multiple communication interfaces within a compact footprint. Integration must account for carrier board compatibility, field signal levels and host system requirements.

As Acromag's representative in France for embedded computing solutions, ECRIN Systems supports system integrators with module selection, cooling options and compatible QMC carrier boards.

For projects requiring a complete embedded subsystem, explore our COTS and Modified COTS expertise.

Specifications

GENERAL
Standard
VITA 93, single-width QMC mezzanine
Air-cooled part number
QMC511-1111
Conduction-cooled part number
QMC512-1111
SERIAL COMMUNICATION
Number of ports
8 independent asynchronous ports
Interfaces
RS-232, RS-422 or RS-485, selectable per port
Interface standards
EIA/TIA-232-F, EIA/TIA-422B, EIA-485
RS-485 operation
Full or half-duplex
Isolation
Non-isolated ports, common return
Maximum data rate
20 Mbps, depending on configuration
Indicative cable length
Up to 1,200 m typical, depending on interface, data rate and cabling
Character length
5 to 8 bits, programmable
Parity
Even, odd or none
Stop bits
1 / 1.5 / 2, programmable
DATA HANDLING
UART register set
16550-compatible
Transmit FIFO
256 bytes per port
Receive FIFO
256 bytes per port
FIFO trigger levels
Programmable
Interrupts
Transmit, receive, line status and communication events
Interrupt register
Centralized interrupt status reading
Flow control
Flow-control and special-character interrupts
TIMING
Timer / counter
16-bit general-purpose
Internal clock
125 MHz
Operating modes
Single-shot or retriggerable
Timer interrupts
Timeout event support
HOST INTERFACE
Bus
PCI Express Gen 1 x1
PCIe specification
PCI Express Base Specification, Revision 2.1
PCIe lanes
1 lane in each direction
PCIe signaling rate
2.5 Gbps
BAR0 memory space
256 KB
BAR2 memory space
1 MB
MODULE MANAGEMENT
QMC connectors
2 × 80-pin connectors
P1 connector
PCIe host and management interface
P2 connector
Serial field I/O signals
EEPROM
Module information and sensor data
Management communication
I²C through compatible carrier
IPMI
Management supported through a carrier with IPMC
POWER
+3,3 V DC
±5%, 0.10 A typical
+3.3 V auxiliary
±5%, 0.20 A typical
+12 V DC
±5%, 0.28 A typical
MECHANICAL
Dimensions
78,25 × 26 × 11 mm
Form factor
Single-width QMC
Carrier board
Compatible VITA 93 QMC carrier required
ENVIRONMENTAL
QMC511 operation
0 to +70°C, air-cooled, 200 LFM
QMC512 operation
−40 to +85°C, conduction-cooled
Storage temperature
−55 to +125°C
Relative humidity
5 to 95%, non-condensing
MTBF
Contact manufacturer
SOFTWARE
Software suite
USW-API
Documented operating systems
Windows, Linux, VxWorks
COMPLIANCE
Indicated markings
CE and RoHS

Resources & documentation

Expand Your Embedded System with 8 QMC510 Serial Ports

Expand Your Embedded System with 8 QMC510 Serial Ports

Looking for a compact serial communication module to add eight RS-232, RS-422 or RS-485 interfaces to your embedded system?

ECRIN Systems supports the selection of the Acromag QMC510, including QMC511 or QMC512 cooling options and identification of a compatible QMC carrier board.

Our technical team can also review data rates, port configuration, field connectivity, data handling and cooling requirements.

Contact our specialists to define your configuration and request a tailored technical quotation.

Other QMC Serial Communication Modules for Embedded Systems

See the range
TQMC402 – 4-Channel Isolated RS232/RS422/RS485 QMC Module

TQMC402 – 4-Channel Isolated RS232/RS422/RS485 QMC Module

The TQMC402 is a VITA 93.0 QMC module featuring four galvanically isolated RS232, RS422 or RS485 serial interfaces. Each channel is independently programmable and supports asynchronous communication up to 20 Mbps in RS422/RS485 modes.
TQMC401 – 4-Channel High-Speed Synchronous/Asynchronous Serial QMC Module

TQMC401 – 4-Channel High-Speed Synchronous/Asynchronous Serial QMC Module

The TQMC401 is a VITA 93.0 QMC module featuring four high-speed synchronous and asynchronous serial channels. Its FPGA-based controller supports multiple protocols, DMA transfers and synchronous data rates up to 10 Mbps.
TQMC400 – 4-Channel QMC RS232/RS422/RS485 Full-Modem Serial Module

TQMC400 – 4-Channel QMC RS232/RS422/RS485 Full-Modem Serial Module

The TEWS Technologies TQMC400 is a VITA 93.0 QMC module featuring four programmable RS232, RS422 or RS485 serial channels. It supports asynchronous communication up to 20 Mbps in RS422/RS485 modes and provides full RS232 modem signals.